I shouldn’t be showing you guy this but fu*k! I’m trying to wake people up out of thier slumber #sleep. So i will share a vidoe in my next post on how to extract your own DMT very easily . It might get removed soon so learn it whiel you can , And of course this is for those that are interested in learning how to extract DMT in the countries where it is still legal WINK WINK.
IINGREDIENTS
- DMT contains plants such as Mimosa hostilis rook back
- Water
- Vinegar
- Naptha VM&P ( if unavailable , 40 -60 Petroleum Ether can be used
Equipments
- Personal safty: fume mask safety goggles and rubber gloves
- Grinder or belnder that is capable of crushing ice
- Glass mixing jar – with a wide mouth and tight fitting lid
- Collection jars with lids x4( glass jelly/jam jars will do
- Coffee filters
- Rubber spatula
- Pipette
- Freezer
- Eyedropper
STEP 1: EXTRACT DMT FROM THE PLANT
- Cut and blend your your plant material until it’s as fine as you can get it- wear a mask to avoid breathing in the powder.
- Slowly add your lye to your water a tablespoon at a time , mixing until dissolved, in your mixing jar, For 50g Mimosa hostilis bark use 750ml water and 50g of lye. Note lye cn cause chemical burns and shoul be treated with care. Neutalise any spills qith vinegar. wear gloves and safety glasses.
- Add your powder plant in the jar, tightly close the lid, shake thoroughly and then leave for about an hour.
STEP 2: EXTRACTING DMT FROM BASE SOLUTION
- Add your naptha to the mixing jar , for 50g Mimosa hostilis bark, use 50ml naptha
- Put the lid back on your mixing jar and gently mixed it for about a minute , turning it upside down a few times . Don’t shake it , as this will make it hard to separate out the two layers later
- Set down your mixing jar and allow allow the two layers to separate.
- Repeat this gentle agitation a few times
- Once the layers have saperated after the final agitation, use your pippette to move the top (clear ) layer into one of your collection jars. This contains your DMT . Try to avaoid taking any of the darker, bottom layer as this contains nasty stuff you don’t want carried over.
- Add more naptha to the mixing jars and repeat the above steps three more times to get every last of the remaining dmt out of the base solution.
- Optional- leave the last batch in the mixing jar for a couple of days to to get the the maximum amount of DMT from the base solution.
- Put all four of your collection jars (contining DMT in a naptha solution)in the freeer and leave overnight.
STEP 3: EXTRACTING THE DMT FROM THE NAPTHAT SOLUTION
- The freezer should have made your DMT crystalise in your collection jars , Pour the solution through the coffee filter to collect the DMT. the naptha can be saved and reused in future extractions
- Use your rubber spatula to get every last bit of naptha solution out of the collection jar
- Carefully lay out your cofffe filter to dry . When dried, this DMT powder is ready to smoke but can be refine further in the optional step below
OPTIONAL STEP 4: RECRYSTALISATION OF DMT FOR FURTHER REFINEMENT
- Put your DMT powder in a small glass container.
- Put your solvent (either napthat or heptane ) in another separate container. You will need about 25ml of solvent for every gram DMT powder.
- Carefully placed both galss container into a pan of hot water , so thier content starts to heat up. Note: your solvent will give off flammable fumes, so DO NOT use a gas stove or have open flames around.
- Use an eyedropper to add tiny bits of your hot solvent to the DMT powder . Swirl the galss conatiner around and keep adding solvent until all the DMT is dissolved . Try to use as little solvent as you can get away with
- Take the pan of water off the heat , and leave it to cool down to room temperature.
- Take the glass container with your dissolved DMT powder. Now at room temperature and put into the fridge
- When it has cool down , move the container into the freezer and leave for a few hours
- You can now filter out your refined DMT crystals using a cofe filter. This process can be repeated for even greater purity.
The Quick Version: How To Extract DMT
Adapted from lazyman’s tek on the DMT nexus
For those of you who don’t look at these steps and ljust want to get your DMT out of your plant quickly as possible (without worrying about puity or yield) here’s is a simple protocol
How do I know the purity of my extracted DMT?
All you have to worry about when you mak your own dmt is how efficient you’ve been following th instructions. if you’ve used poor quality ingredients , or done a messy job(i.e carried over some of the base solution byy accident ) you may end up with more impurities in your DMT powder. This can be umpleasant to smoke.
There’s the myth that the colour of DMT powder tells you it’s purity – this isnt’t true . as there are number of factors that can contribute to the colour of DMT powder . Generally, if your powder is white, yellow , red or brown, it is safe to smaoke . if it is blue or green, something ahsve gone wronh with your extractionand you should try again
Alternative Extraction Guides
As mention earleir, many extraction protocols use an acid/base extractionmethod, whcih we haven’t covered as the straight -to base methodis a lot simpler.
